ELECTRIC VEHICLE KITS
we now have complete kits available for the Mazda Miata, designed
for the first generation (89-97)
The adaptor plates, coupling,spacer and mount will     also fit the
second generation, (98-04)
This is the rear battery box, designed
to fit in place of the gas tank, above
the rear axle. Designed to hold 5
optima 12 volt D31T batteries. This
requires some sheet metal removal,
but
no structural modifications. Made
of 1/8" aluminum (6061 T-6), with
structural support under base.
Here is what these parts
look like on a warp9 motor.
This is the front battery box, designed
to fit in front of the firewall, above the
motor using D31T batteries. This will
require new hydraulic brake lines to be
made up.
These battery boxes are designed to keep close to the "50-50" weight distribution that the
miata originally had. It adds 5 batteries directly over the rear axle and 5 over the front axle.

Build a car for you, not for them ! (the oil
companies!)
                                                
Here is the front motor bracket for
power           steering, air conditioning,  on the
mazda           miata.
 Made from 6061-T6
aluminum




This bracket could be ordered as just the right
angle plate (without pulley hub and P/S and
A/C brackets), to be used on other
applications with the warp 9 motor,
may need
to be modified
for your application.
Front motor bracket shown on Warp 9
motor - with belt tensioner pulley,
power steering, air conditioning, and
alternator mounted. Also visible is the
this front bracket.
MOTOR MOUNT  made of 1/4" 6061-T6 aluminum    fits '89 to '04 Miata
Made for the WARP 9 motor, but may fit other 9" motors
These kits are designed to be complete with nothing else to
purchase.                                                   
(Except hardware, low voltage wiring,
and batteries)
Kits can be bought separate or all together. Some substitutions or
deletions are available.   
DRIVELINE KIT includes:        No longer available             
Warp 9 motor
Controller
-choice of Curtis 1231c or upgrade to high perf controller below
Overnight charger
Linear throttle
(soliton throttle with soliton 1 controller)

Upgrade charger to NetGain (144/156v systems)
Upgrade controller to WarpDrive controller -pricing TBA
Upgrade to the new
Soliton 1 controller  available- pricing TBA
*******KITS ARE NO LONGER AVAILABLE  *******
MOUNTING KIT includes:   No longer available               
Transmission adapter plate
Coupling
Motor mount
(with rubber insert)


made of 6061-T6 aluminum
ACCESSORY KIT for use with A/C and power steering   includes:          
Front motor plate (ties to mount)
Pulley hub (uses original pulley)
A/C compressor spacers
belt
idler                    
No longer available
ELECTRICAL KIT includes:              No longer available
1/0 welding cable                                                                     500 or 800 amp meter
HD lugs, straight, angle                                                             meter shunt
shrink tubing                                                                            Curtis "fuel gauge"
500 amp fuse                                                                            Time delay relay and base
fuse holder                                                                               Standard relays
contactor, Kilovac w/coil economizer and aux contacts             inertia switch
precharge resistor                                                                  small fuse holder
terminal boots                                                                          50 amp charger anderson connector and cover
liquidtite conduit, large and small                                           High voltage warning sticker
liquidtite fittings,straight, angle                                               Cable clamps
cord grips                                                                                 Charge port
BATTERY BOX KITS  include:                      No longer available            
Front battery box
Mounts
Fiberglass angle holdown with FG bolt and nut
Lid
                                                                           
Rear battery box
Mounting material
Lid

Battery boxes are designed to keep  as close as possible to the 50/50 weight distribution as original. If
144volt system is desired, a third box has to be added under the trunk floor, manufactured at extra
cost.(and offsetting that 50/50 balance)
These boxes are designed for group 31 AGM batteries, 5 in front over the axle, 5 in rear over the axle.
Lithium boxes in development, if these are your requirements, e-mail us
.
OPTIONS:
Tachometer interface with rev limit function
Paktrakr battery monitoring system
Vacuum pump kit
(if car has power brakes)
Vacuum pump accessory kit (hose,reservoir,muffler,fittings for res)
Tire pressure monitoring system
Front coil spring spacers
DC-DC converter
12 vdc charger for aux battery
Trans cooler/pressure gauge kit
(for automatic trans cars)
Heater
Auto eject charge port
Charging cord
PERFORMANCE SPECIFICATIONS
TOP SPEED:  80 MPH     RANGE:  23 miles @ 35mph 80% DOD with 75ah lead acid AGM 120volt pack
     27 miles @ 35mph 80% DOD with 75ah
lead acid AGM 144volt pack (est)
     37 miles @ 35mph 80% DOD with 100ah
lead acid AGM 144volt pack (est)
     
 LifePO4 batteries can add significantly more range
ACCELERATION:  ------  0-30 in 5.5 seconds  ------  0-40 in 8.7 seconds  ------  0-50 in 15.5 seconds

WEIGHT: ---  2740 LBS   --  1400 LBS FRONT,   --   1340 LBS REAR     
Car built with 75ah batteries, car can be built with 100ah odessey agm batteries or different combinations of lithiums.
These are actual performance specs obtained by EV-propulsion llc staff using new batteries with
average driving style. Range may increase after batteries have 20+ cycles on them. Range may increase
with lighter driving style. Larger AH  battery pack and higher voltage will also increase range.
Your                   actual range may vary due to driving style, speed and terrain.
FABRICATED PARTS
ADAPTER PLATE   made from 6061-T6 aluminum  fits '89-'04 Miata  
This adapter gives you the correct transmission mounting
distance                  from the motor shaft when used with the coupler
below
Made for the WARP 9 motor bolt pattern, but will fit other
9"                               motors with the same mounting bolt design
SHAFT COUPLER  Made of steel
FOR MANUAL OR AUTOMATIC MIATA TRANSMISSIONS
Fits  '89 to '04 Mazda Miata
BATTERY BOXES  Made of 6061-T6 aluminum
Fits '89 to '97 Mazda Miata
FRONT ACCESSORY BRACKET
No longer available
No longer available
Mazda Miata Motor Adapter.

6061-t6 Billet construction.  Includes radial and thrust bearing
motor coupling system.
Unparalleled quality and design.

No longer available
EV-PROPULSIONllc
"The EV CONVERSIONISTS'"
conversions since 1975
QUALITY ELECTRIC VEHICLE CONVERSIONS AND QUALITY PARTS
                        
NEW ITEMS
New design adapter and coupler
now one unit!
Old design, no longer
available
We are now using the
new design shown
above, these are no
longer available .
NOTE: We are now using only the new design adapter plate and coupler unit in our kits.
The old style parts are only available as replacements for previously sold units.